| S6062 series of Electric Control Actuators |
|
| |
 
S6062-500N S6062-1000N |
|
| |
The S6062 series is non-spring return, synchronous motordriven reversible actuators are available for 3 point (floating) or with electric positioned for 0-10 V control. They factory calibrated pressure switches to provide specified closeoff ratings.
|
|
| |
There actuators are available in four sizes with 500N,1000N, 1800N and 3000N nominal force and can be used with flanged valves according to maximum close-off pressure ratings specified. |
|
| |
Analogue models: (modulating) |
|
| |
·S6062-05A 500N |
|
· S6062-10A 1000N |
|
| |
·S6062-18A 1800N |
|
· S6062-30A 3000N |
|
| |
Specification |
|
| |
Action |
: |
0 - 90° (in 5° increments) |
|
| |
Control |
: |
24VAC/24VDC, 220VAC 50/60Hz
110VAC 50/60Hz |
|
| |
Input signal |
: |
6.5W , 7.5W |
|
| |
Motor |
: |
Digital : On/off; 3-floating points,
Analogue : modulating 0(2) ~ 10V/0(4) ~ 20mA proportional input |
|
| |
Operating voltage |
: |
0(2) - 10V max 2mA |
|
| |
Force |
: |
Cylinder shaft size: 20 mm
Square shaft size: 16 x 16mm |
|
| |
Material |
: |
100(L) x 180(H) x 67.3(W) mm |
|
| |
Protection |
: |
ABS engineering plastic |
|
| |
Ambient temperature |
: |
Operation: -20 - 50°
5 - 95% RH non condensing
Storage: -40 - 80° |
|
| |
Relative humidity |
: |
IP44 |
|
| |
Digital models: (On/off) |
|
| |
S6062-05D 500N
S6062-18D 1800N |
:
|
· S6062-10D 1000N
· S6062-30D 3000N |
|
| |
Specification |
|
| |
S6062-05D, 10D, 18D, 30D:On-Off actuator providing incremental control, assembled with reversing motor. |
|
| |
Action |
: |
reversible |
|
| |
Control |
: |
incremental |
|
| |
Input signal |
: |
0-10VDC
0-20 (4-20)mA |
|
| |
Motor |
: |
Synchronous and reversible |
|
| |
Operating voltage |
: |
24VAC 50/60Hz 2.4W |
|
| |
Force |
: |
500N, 1000N, 1800N, 3000N |
|
| |
Material |
: |
Gear : nylon
Support base : galvanized steel
Yoke : die cast aluminum
Cover : ABS |
|
| |
Protection |
: |
S6062-500/1000N : IP42
S6062-1800N/3000N : IP54 |
|
| |
Ambient temperature |
: |
Operation : -10 - 60°C
Storage : -10 - 60°C |
|
| |
Relative humidity |
: |
0-90% RH, non condensing |
|
| |
|
|
| |
Matching nominal diameters of valves with actuator |
|
| |
|
|
| |
Mounting Instruction |
|
| |
It is recommended that the valves be mounted in the upright position in a conveniently accessible location. When mounted horizontally, the yoke should be fitted such that the stanchions are positioned vertically one above the other.
The actuator must be protected against dripping water, which could enter the housing and damage the mechanism or motor.
The actuator must not be covered with insulating material. |
|
| |
Wiring instruction |
|
| |
All wiring must be in accordance with local regulations and national electrical codes, and should be carried out by authorized personnel only.
Make sure that the line power supply is in accordance with the power supply specified on the device. |
|
| |
Warning! |
|
| |
Disconnect the power supply before attempting to do wiring connection to avoid personal injury.
Do not attempt to touch or disconnect wires when power is turned on. |
|
| |
Ordering code |
|
| |
|
